Product Description
REPLACED BY NEW MODEL: BENDPAK 10AP
FREE TRUCK / VAN ADAPTER
Clearfloor Versatility – Rugged Dependability-Low-Profile Arms
The safe and rugged XPR-10-LP two-post lift, CE approved and certified, features ourexclusive Low-Pro™ arms that accommodate lowered sports cars and those vehicles with exclusive lift points located on the extreme outer edges of the chassis. A telescoping overhead structure provides the convenience of wide or narrow installation wrapped up into one configurable package. This unique configurable design allows you to choose the best setting for your specific space or vehicle lifting requirements. The highly sophisticated yet simple and dependable XPR-Series design requires very little service or maintenance for an overall lower cost of ownership. All BendPak's XPR two-post models feature dual "direct-drive" low-pressure cylinders, maintenance-free UHMW load bearings, single-piece columns, extra-tall lifting carriages and double telescoping arm configuration for increase arm positioning versatility.
Clearfloor convenience
Our clearfloor models provide unobstructed floor space allowing technicians to easily move toolboxes, transmission jacks, oil drains and other equipment underneath the elevated vehicle.
Telescoping Low-Pro™ arms.
The safe and rugged XPR-10-LP two-post lift features our exclusive Low-Pro™ armsthat accommodate lowered sports cars and those vehicles with exclusive lift points located on the extreme outer edges of the chassis.
Optional column extension
Gives you the flexibility of increasing the overhead clearance to maximize the vehicles you can service.
Included truck and van adapters
Others might charge extra for these necessary adapters, but they're standard with every XPR-Series lift. Ideal for trucks and vans with running boards or auxiliary fuel tanks.
Lowered arm tube supports
To minimize the chance of damaging vehicles with low-hanging vehicle doors, we completely redesigned our arm tube supports to allow for better clearance.
Automatic arm restraints
Each arm is equipped with durable arm restraints that automatically engage each time the lift is raised. When the lift is lowered, the gear arm restraints automatically disengage to provide easy positioning of the lift arms.
Taller lift carriages
Take a close look at our lift carriages (the lifting assembly that the arms are attached to) and then take a look at the competition. You'll notice our 53" tall carriages are considerably taller than most, which minimizes the stress placed on the load bearings and columns.
Maintenance-free load bearings
Rather than using roller bearings that need to be constantly lubricated, every XPR-Series lift carriage uses high-tech UHMW (ultra-high molecular weight polyethylene) load bearings that never need lubrication and are designed to last the entire life of the lift.
Single-piece columns
We purposely manufacture the columns using single-piececonstruction for added strength and less fatigue under heavy load conditions.
Dual direct-drive technology
By utilizing two, low-pressure HVLP direct-drive cylinders, we've eliminated the need for lifting chains or screw mechanisms most commonly found on other lift designs. HVLP direct-drive technology offers better reliability, smoother operation and less maintenance. High-volume, low-pressure equates to less workload placed on the entire hydraulic system.
Single-point safety release
The single point safety release and "dead man" style operation controls makes every one of our XPR-Series lifts easy to operate and safe to use.
On the level
Our dual-synchro equalization system maintains equal lifting and provides operators with a stable, level vehicle working condition.
Auto shutoff
A rigid, padded safety shutoff bar automatically stops the lift should a vehicle come in contact with overhead structure.
Industrial-grade hydraulic cylinders
High-speed hydraulics
Free-flow, high-pressure 3/8" hydraulic lines, a high-flow pump and integrated AC power-unit increase ascent and descent speed rates for enhanced productivity.
Durable powder-coat finish
All XPR-Series lifts feature a durable powder-coat finish that gives the metal a high-quality, extremely durable finish which can withstand even the harshest environmental or chemical conditions. Unlike other companies that claim to powder coat, we take pride in our meticulous 10-step process. First, all parts are visually inspected before being sandblasted. Afterwards, the parts are washed in our 5-stage phosphate tanks that can accommodate parts up to 25' long. Once cleaned, they're immediately dried to avoid rust production, and then outgassed.
Outgassing pre-bakes the parts in a curing oven, reducing the possibility of blemishes that may be hiding in the pores of the metal. If not properly outgassed, imperfections in the metal may bubble during the curing process and most likely will cause chips in the powder. After the parts are washed and outgassed, any surfaces and / or threaded holes that need to be masked or plugged, are done so with high-temperature masking tape and silicone plugs. Next, the parts are given a quick thinner wipe to remove any light debris or fingerprints, before being hung on an electrostatically grounded conveyor line. The powder is finally applied using an electrostatic spray gun. The powder "sticks" to the surface in a fashion similar to how dust sticks to a television screen. Once the parts are powder coated, the carts are rolled into our curing oven and baked at 400° F for 45 minutes.
Detailed instructions
Included with every lift are detailed installation and maintenance instructions, graphic safety decals, maintenance decals, vehicle lifting point guide and a safety instruction placard to train personnel on proper safety procedures and maintenance guidelines.
Features
- Lift arms shown with optional foot guards
- 10,000-lb lifting capacity
- CE Approved and Certified. Meets or exceeds the standards prescribed by European Standard EN 1493
- Telescoping Low-Pro™ arms accommodate lowered sports cars and those vehicles with lift points located on outer edges of the chassis
- Expandable top beam accommodates wide or narrow configuration
- Padded overhead safety shutoff bar
- Single-piece columns
- Dual hydraulic direct-drive cylinders
- Oversized 53" tall carriage for superior strength and durability
- Electric / hydraulic power system
- Large, 17" x 19" A36 steel base plate
- Self-lubricating dura-glide UHMW polyethylene bearing system
- Single-point safety release
- Safety locks in each column spaced every 3"
- Automatic arm restraints
- Heavy-duty 3/8" aircraft-quality equalizer cables
- Oversized cable sheave diameter reduces cable fatigue
- 8-piece truck and van adapter set standard
- Versatile drop-in contact pads with stackable adapters
- Meets or exceeds the standards prescribed by ANSI/ALI ALCTV-2011
Specs
- Lifting capacity*: 10,000 lbs. / 4,536 kg
- *Max capacity / front axle: 5,000 lbs. / 2,268 kg
- *Max capacity / rear axle: 5,000 lbs. / 2,268 kg
- Overall height: 145" / 3,683 mm
- Overall width - NARROW CONFIG: 132" / 3,353 mm
- Overall width - WIDE CONFIG: 145" / 3,683 mm
- Width outside of columns (NARROW): 126-3/4" / 3,220 mm
- Width outside of columns (WIDE): 139-3/4" / 3,555 mm
- Floor to overhead switch*: 141" / 3,581 mm
- Inside columns (NARROW): 105.5" / 2,680 mm
- Inside columns (WIDE): 118.5" / 3,010 mm
- Front arm min reach: 28-1/2" / 724 mm
- Front arm max reach: 47-1/2" / 1,206 mm
- Rear arm min reach: 28-1/2" / 724 mm
- Rear arm max reach: 47-1/2" / 1,206 mm
- Min pad height: 4" / 102 mm
- Rise: 69" / 1,753 mm
- Lift height max (pad only): 73" / 1,854 mm
- Lift height max (6" adapter): 79" / 2,007 mm
- Motor: 220 VAC / 60 Hz / 1 Ph
- Time to full rise: 45 sec
- Max load per arm: 2,500 lbs. / 1,134 kg